|
|
搜索"C5402def.h"看看~~~簡單明了~~~
雖然C5402cfg.h/c5402cfg.c"更強大，俺暫不想發布~~~
void McBSPObj::McBSP0Init(void)//McBSP從設備SPI硬件配置
{
/*-------------------------------------------------------------
DSP5402之McBSP從設備SPI硬件四種模式配置實例(經過硬件測試)
--------------------------------------------------------------*/
//PCR設置過程(FSM=0,CLKM=0)
McBSP0->SPSA = PCR;
McBSP1->SPSD = (0 << PCR_XIOEN) //發送非通用I/O模式位
| (0 << PCR_RIOEN) //接收非通用I/O模式位
| (0 << PCR_FSXM) //外部發送幀同步脈沖(外部片選)
| (0 << PCR_FSRM) //外部接收幀同步脈沖(外部片選)
| (0 << PCR_CLKXM) //外部發送時鐘(外部時鐘源)
| (0 << PCR_CLKRM) //外部接收時鐘(外部時鐘源)
#if SPIMODE == 0
//SPI設置過程00(0--FS高電平有效,0--CLK上升沿收發數據)
| (0 << PCR_FSXP) //發送幀同步脈沖極性(高電平有效)
| (0 << PCR_FSRP) //接收幀同步脈沖極性(高電平有效)
| (0 << PCR_CLKXP) //發送時鐘極性(上升沿發送數據)
| (0 << PCR_CLKRP);//接收時鐘極性(上升沿接收數據)
#endif
#if SPIMODE == 1
//SPI設置過程01(0--FS高電平有效,1--CLK下降沿收發數據)
| (0 << PCR_FSXP) //發送幀同步脈沖極性(高電平有效)
| (0 << PCR_FSRP) //接收幀同步脈沖極性(高電平有效)
| (1 << PCR_CLKXP) //發送時鐘極性(下降沿發送數據)
| (1 << PCR_CLKRP);//接收時鐘極性(下降沿接收數據)
#endif
#if SPIMODE == 2
//SPI設置過程10(1--FS低電平有效,0--CLK上升沿收發數據)
| (1 << PCR_FSXP) //發送幀同步脈沖極性(低電平有效)
| (1 << PCR_FSRP) //接收幀同步脈沖極性(低電平有效)
| (0 << PCR_CLKXP) //發送時鐘極性(上升沿發送數據)
| (0 << PCR_CLKRP);//接收時鐘極性(上升沿接收數據)
#endif
#if SPIMODE == 3
//SPI設置過程11(1--FS低電平有效,1--CLK下降沿收發數據)
| (1 << PCR_FSXP) //發送幀同步脈沖極性(低電平有效)
| (1 << PCR_FSRP) //接收幀同步脈沖極性(低電平有效)
| (1 << PCR_CLKXP) //發送時鐘極性(下降沿發送數據)
| (1 << PCR_CLKRP);//接收時鐘極性(下降沿接收數據)
#endif
//MCR1設置過程(RMCM=0)
McBSP0->SPSA = MCR1;//
McBSP0->SPSD = (0 << MCR1_RMCM) //允許接收多通道選擇(0)
| (0x00 << MCR1_RPBBLK)
| (0x00 << MCR1_RPABLK)
| (0x00 << MCR1_RCBLK);
//MCR2設置過程(XMCM=0)
McBSP0->SPSA = MCR2;//
McBSP0->SPSD = (0x00 << MCR2_XMCM) //允許發送多通道選擇(00b)
| (0x00 << MCR2_XPBBLK)
| (0x00 << MCR2_XPABLK)
| (0x00 << MCR2_XCBLK);
//RCERA設置過程
McBSP0->SPSA = RCERA;//
McBSP0->SPSD = 0;
//RCERB設置過程
McBSP0->SPSA = RCERB;//
McBSP0->SPSD = 0;
//XCERA設置過程
McBSP0->SPSA = XCERA;//
McBSP0->SPSD = 0;
//XCERB設置過程
McBSP0->SPSA = XCERB;//
McBSP0->SPSD = 0;
//XCR1設置過程
McBSP0->SPSA = XCR1;//
McBSP0->SPSD = (0x00 << XCR1_XFRLEN1) //每幀1個字(每幀中斷的次數1!!!)
// | (0x02 << XCR1_XWDLEN1);//每字16位長(每次中斷的字節數2!!!)
| (0x00 << XCR1_XWDLEN1);//每字8位長(每次中斷的字節數2!!!)
//XCR2設置過程
McBSP0->SPSA = XCR2;
McBSP0->SPSD = (0 << XCR2_XPHASE) //單相幀(其他設置都為0)
| (0x00 << XCR2_XCOMPAND)//發送數據從最高位(MSB)開始
| (0x00 << XCR2_XDATDLY);//同步后延遲0位數據
//RCR1設置過程
McBSP0->SPSA = RCR1;
McBSP0->SPSD = (0x00 << RCR1_RFRLEN1) //每幀1個字(每幀中斷的次數1!!!)
// | (0x02 << RCR1_RWDLEN1);//每字16位長(每次中斷的字節數2!!!)
| (0x00 << RCR1_RWDLEN1);//每字8位長(每次中斷的字節數2!!!)
//RCR2設置過程
McBSP0->SPSA = RCR2;
McBSP0->SPSD = (0 << RCR2_RPHASE) //單相幀(其他設置都為0)
| (0x00 << RCR2_RCOMPAND)//接收數據從最高位(MSB)開始
| (0x00 << RCR2_RDATDLY);//同步后延遲0位數據
//SRGR1設置過程
McBSP0->SPSA = SRGR1;
McBSP0->SPSD = (0x00 << SRGR1_CLKGDV);//1
//SRGR2設置過程
McBSP0->SPSA = SRGR2;
McBSP0->SPSD = (0 << SRGR2_FSGM)
| (1 << SRGR2_CLKSM)//由CPU時鐘產生的采樣率時鐘1
| (0 << SRGR2_CLKSP)//0
| (1 << SRGR2_GSYNC)//
| (0x0f << SRGR2_FPER);//0x0f
//SPCR1設置過程(CLKSTP=1Xb,RINTM=00b)
McBSP0->SPSA = SPCR1;
McBSP0->SPSD = (0x00 << SPCR1_RINTM) //接收中斷模式00(每幀接收1次中?
| (0 << SPCR1_DLB) //禁止回送
| (1 << SPCR1_DXENA) //DX使能
| (0x00 << SPCR1_RJUST) //接收符號不擴展
| (0x02 << SPCR1_CLKSTP);//SPI模式時鐘開始于上升沿（無延遲）
//SPCR2設置過程(XINTM=02b)
McBSP0->SPSA = SPCR2;
McBSP0->SPSD = (0x02 << SPCR2_XINTM)//發送中斷模式02
| (1 << SPCR2_XEMPTY) //發送移位寄存器空
| (1 << SPCR2_XRDY); //發送準備好
//SPCR1復位過程
McBSP0->SPSA = SPCR1;
McBSP0->SPSD|= (1 << SPCR1_RRST);//接收器復位
//SPCR2復位過程
McBSP0->SPSA = SPCR2;
McBSP0->SPSD|= (1 << SPCR2_XRST)//發送器復位
| (1 << SPCR2_GRST)//采樣率發生器復位
| (1 << SPCR2_FRST);//幀同步發生器復位
//清除允許BXINT0中斷過程
// SREG->IFR = (1 << IFR_BXINT0);//清除BXINT0中斷標志
// SREG->IMR |= (1 << IMR_BXINT0);//允許BXINT0中斷
//清除允許BRINT0中斷過程
SREG->IFR = (1 << IFR_BRINT0);//清除BRINT0中斷標志
SREG->IMR |= (1 << IMR_BRINT0);//允許BRINT0中斷
}
void McBSPObj::McBSP1Init(void)//GPIO配置
{
McBSP1->SPSA = SPCR1;
McBSP1->SPSD = 0;
McBSP1->SPSA = SPCR2;
McBSP1->SPSD = 0;
McBSP1->SPSA = PCR;
//設置收發為IO接口,DX輸出,DR,CLKS輸入
McBSP1->SPSD = (1 << PCR_RIOEN) //通用I/O模式位
//硬件RDDOG喂狗信號(BDX1)管腳輸出模式默認I/O設置
| (1 << PCR_XIOEN) //通用I/O模式位
//硬件RD SIA信號(BFSR1)管腳輸入模式設置
| (0 << PCR_FSRM) //FSR為輸入IO
//硬件FM CE信號(BFSX1)管腳輸出模式設置
| (1 << PCR_FSXM) //FSR為輸出IO,FLASH的片選信號
//硬件FM CE信號(BFSX1)管腳高電平輸出控制
| (1 << PCR_FSXP) //關閉FLASH的片選信號(FSX=1)
| (0 << PCR_CLKRM) //CLKR為輸入IO
| (0 << PCR_CLKXM); //CLKX為輸入IO,CLKX信號
}
菜農HotPower@126.com |
|
發表于 2009-4-2 22:01:00
收藏
頂
踩